ENTRELEC
011668927
Entrelec Series "11 000" 12 wire empty body
A series 11 000 module is made of three parts:
Body of molded polyamide holding the terminals.
This insulator has 12 wire clamps on the upper half of the module.
On the lower half, this body can receive up to 12 wire-wrapping tabs.
Body can hold PCB PN# 017520707
Additional Part Information
A series 11 000 module is made of three parts:
Body of molded polyamide holding the terminals.
This insulator has 12 wire clamps on the upper half of the module.
On the lower half, this body can receive up to 12 wire-wrapping tabs.
Body can hold PCB PN# 017520707
Additional Part Information
Our price: $16.03
011823327
Entrelec FEM16 end section for M35/16 block
When assembled on the mounting track, terminal blocks cover each other's open side.
At the end of an assembly, or when the size of the blocks change in an assembly,
an end section must be used to isolate the open side of the block.
End sections are available for all terminal blocks and are sometimes available in colours.
Coloured end sections can offer an easy and economical way to separate circuits for identification.
Additional Part Information
When assembled on the mounting track, terminal blocks cover each other's open side.
At the end of an assembly, or when the size of the blocks change in an assembly,
an end section must be used to isolate the open side of the block.
End sections are available for all terminal blocks and are sometimes available in colours.
Coloured end sections can offer an easy and economical way to separate circuits for identification.
Additional Part Information
Our price: $0.78
017622622
Entrelec BJM5D 2 pole jumper for 5mm spacing
Use the BJ jumper bar to connect consecutive and non consecutive terminal blocks with the same spacing.
Jumper bar includes a metal tube wich makes contact with the terminal block's internal connector bar.
To mount the BJ jumper bar accessory onto terminal blocks still having top center partitions, the user must cut out all partitions between the blocks.
When the BJ jumper bar is used with each of two series of connected blocks,
the top center opening at the junction of the two series must be closed by a circuit separator or a separator end section
SCM, SCF or SCD to permit different voltage potentials on each series jumper bar accessory.
Simplified model, composed of a bar prepunched to the spacing of the blocks, and of captive screws and spacers
Additional Part Information
Use the BJ jumper bar to connect consecutive and non consecutive terminal blocks with the same spacing.
Jumper bar includes a metal tube wich makes contact with the terminal block's internal connector bar.
To mount the BJ jumper bar accessory onto terminal blocks still having top center partitions, the user must cut out all partitions between the blocks.
When the BJ jumper bar is used with each of two series of connected blocks,
the top center opening at the junction of the two series must be closed by a circuit separator or a separator end section
SCM, SCF or SCD to permit different voltage potentials on each series jumper bar accessory.
Simplified model, composed of a bar prepunched to the spacing of the blocks, and of captive screws and spacers
Additional Part Information
Our price: $1.97
017622723
Entrelec BJM5D 3 pole jumper for 5mm spacing
Use the BJ jumper bar to connect consecutive and non consecutive terminal blocks with the same spacing.
Jumper bar includes a metal tube wich makes contact with the terminal block's internal connector bar.
To mount the BJ jumper bar accessory onto terminal blocks still having top center partitions, the user must cut out all partitions between the blocks.
When the BJ jumper bar is used with each of two series of connected blocks,
the top center opening at the junction of the two series must be closed by a circuit separator or a separator end section
SCM, SCF or SCD to permit different voltage potentials on each series jumper bar accessory.
Simplified model, composed of a bar prepunched to the spacing of the blocks, and of captive screws and spacers
Additional Part Information
Use the BJ jumper bar to connect consecutive and non consecutive terminal blocks with the same spacing.
Jumper bar includes a metal tube wich makes contact with the terminal block's internal connector bar.
To mount the BJ jumper bar accessory onto terminal blocks still having top center partitions, the user must cut out all partitions between the blocks.
When the BJ jumper bar is used with each of two series of connected blocks,
the top center opening at the junction of the two series must be closed by a circuit separator or a separator end section
SCM, SCF or SCD to permit different voltage potentials on each series jumper bar accessory.
Simplified model, composed of a bar prepunched to the spacing of the blocks, and of captive screws and spacers
Additional Part Information
Our price: $2.52
019905906
Entrelec D2.5/8 ADO terminal block
The ADO System eliminates the need for individual wire stripping and clamp screw tightening,
featuring a secure, vibration and corrosion-free connection with increased wiring productivity
Additional Part Information
The ADO System eliminates the need for individual wire stripping and clamp screw tightening,
featuring a secure, vibration and corrosion-free connection with increased wiring productivity
Additional Part Information
Our price: $1.26
019916626
ABB/Entrelec ML 10/13.SFD Fuse Holder
LED Blown Fuse Indicator
For 1/4" X 1" And 1/4" X 1-1/4" Fuses
Maximum UL Current: 25A
Additional Part Information
LED Blown Fuse Indicator
For 1/4" X 1" And 1/4" X 1-1/4" Fuses
Maximum UL Current: 25A
Additional Part Information
Our price: $17.69
1000421
ABB/Entrelec RB 121 A Relay Module
SPDT
Maximum Current: 10 Amps
Coil Voltage: 24 Volts AC/DC
Additional Part Information
SPDT
Maximum Current: 10 Amps
Coil Voltage: 24 Volts AC/DC
Additional Part Information
Our price: $31.94
